10.1-inch Smart Home Control Panel for Home Assistant Review — Is It Worth It? [2026]
.jpg)
10.1-inch Home Assistant Control Panel
A wall-mountable ESP32-P4 touchscreen with Home Assistant firmware pre-installed, so no coding is needed.
Is the Home Assistant panel worth buying?
If you already run Home Assistant and want a dedicated wall dashboard, this is a tidy shortcut. The firmware is pre-installed, setup is Wi-Fi, your server details and a companion app on the server, and you skip the ESP32 coding and LVGL work. It is not a hub, though, so it is useless without an existing Home Assistant server, and the case is not included.
A ready-made wall panel for Home Assistant
The panel is built on CrowPanel Advanced 10.1-inch ESP32-P4 hardware: dual-core RISC-V up to 400 MHz, 32MB PSRAM and 16MB flash behind a 1024 x 600 IPS capacitive screen at 400 nits. It is $139.90 without a camera or $147.90 with one. The listing says the kit is the display without a case.
What makes it stand out
Three steps, no firmware work
Connect to Wi-Fi, enter your Home Assistant details, then install the supplied companion app on the server. The panel mirrors dashboards, cards and scenes you already configured.
10.1-inch IPS, 400 nits
A 178-degree viewing angle and 400 cd/m2 brightness are fine for a hallway or living room. Touch is capacitive, single or 5-point.
Wi-Fi 6 and Bluetooth 5.3
The ESP32-P4 board lists Wi-Fi 6 on 2.4GHz and Bluetooth 5.3 and BLE. Zigbee, LoRa, Matter, Thread and Wi-Fi HaLow are optional extras.
Audio, GPIO, UART, I2C and SD
Dual speakers and a microphone are built in, and there are headers for GPIO, UART, I2C, USB, an SD card and a battery socket if you want to experiment later.
Full spec sheet
| Main chip | ESP32-P4NRW32 |
| CPU | Dual-core RISC-V up to 400 MHz (HP), single-core 40 MHz (LP) |
| Memory | 32MB PSRAM, 16MB flash |
| Firmware | Home Assistant pre-installed |
| Screen | 10.1-inch IPS, 1024 x 600 |
| Touch | Capacitive, up to 5-point |
| Brightness | 400 cd/m2 typical |
| Wi-Fi / Bluetooth | Wi-Fi 6 (2.4GHz) / Bluetooth 5.3 BLE |
| Power input | 5V/2A |
| Dimensions | 248 x 147 mm |
| Operating temp | -20 to 70 C |
| Included | ESP32-P4 10.1-inch display for Home Assistant (without case) |
Pros & Cons
Pros
- Pre-installed Home Assistant firmware.
- No ESP32 coding or LVGL development.
- Bright 10.1-inch capacitive touchscreen.
- Speakers, microphone and expansion headers.
- Optional camera version for $8 more.
Cons
- Needs an existing Home Assistant server.
- Not a standalone hub.
- Case is not included.
- Wi-Fi is listed as 2.4GHz.
- No customer ratings on the page.
Answers before you buy
Does it work without Home Assistant?
Do I need to code?
Is a case included?
Is there a camera version?
Is the TEELACODES code valid?
A shortcut to a wall dashboard
For Home Assistant owners this is a quick, low-effort way to put a control panel on the wall. Just remember the case and server are your responsibility.
This page contains affiliate links. Teelacodes may earn a commission when you click through and complete a qualifying purchase, at no extra cost to you. Read the full disclosure policy. Prices, stock and promotion terms can change without notice — always confirm the final total and availability on crowpi.cc before ordering.
Popular Blog
